Note: Specifications listed below are for non-AS Grades. For AS Grades the specifications are all the same, except that “AS” is added to the Grade Reference, and the Part Number reads “-110-” in place of “-100-”.
| Nominal Hose Size | *Actual Hose Bore Size | Hose Grade | Outside Diameter of Tube or Braid | Minimum Bend Radius | Maximum Working Pressure (MWP) | Weight per Unit Length | Hose Part Number | ||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| in | mm | in | mm | in | mm | in | mm | Bar | psi | Kg/mtr | lbs/Ft | ||
| 3/8 | 10.0 | 1/4 | 6.3 | TO SS PB |
0.420 0.470 0.512 |
10.70 11.95 13.00 |
1 3/4 1 |
25 19 25 |
4 60 30 |
58 870 435 |
.057 .144 .091 |
.038 .096 .061 |
71-100-06 71-100-06-01-02 71-100-06-01-21 |
| 1/2 | 12.0 | 3/8 | 9.5 | TO SS PB |
0.555 0.600 0.662 |
14.10 15.25 16.80 |
11/2 1 11/2 |
38 25 38 |
4 47 23.5 |
58 680 340 |
.076 .195 .125 |
.051 .130 .084 |
71-100-08 71-100-08-01-02 71-100-08-01-21 |
| 5/8 | 16.0 | 1/2 | 12.7 | TO SS PB |
0.780 0.835 0.906 |
19.80 21.20 23.00 |
2 11/2 2 |
50 38 50 |
4 40 20 |
58 580 290 |
.126 .296 .188 |
.084 .194 .126 |
71-100-10 71-100-10-01-02 71-100-10-01-21 |
| 3/4 | 20.0 | 5/8 | 16.0 | TO SS PB |
0.835 0.894 0.973 |
21.20 22.70 24.70 |
3 2 21/2 |
75 50 63 |
3 32 16 |
43 460 230 |
.166 .376 .226 |
.111 .251 .151 |
71-100-12 71-100-12-01-02 71-100-12-01-21 |
| 1 | 25.0 | 7/8 | 22.0 | TO SS PB |
1.143 1.204 1.300 |
29.00 30.60 32.90 |
31/2 21/2 3 |
89 63 75 |
3 26 13 |
43 380 190 |
.235 .533 .314 |
.157 .310 .210 |
71-100-16 71-100-16-01-02 71-100-16-01-21 |
| 1 1/4 | 32.0 | 11/8 | 28.0 | TO SS PB |
1.349 1.420 1.537 |
34.20 36.00 39.00 |
4 3 31/2 |
100 75 89 |
2 25 12.5 |
29 360 180 |
.342 .729 .444 |
.229 .489 .298 |
71-100-20 71-100-20-01-02 71-100-20-01-21 |
*Visiflon Hose assemblies require that the convolutions at the ends of the hose are opened out to accept either Hydraulic or PTFE Tail end fittings (see Assembly Instructions).
Note: Many of the sizes of hose and fittings listed in this brochure are available as ex-stock items and are priced accordingly. However, some of the less popular items are not always in stock, and may therefore incur a minimum order charge or a set-up charge for smaller quantities. Aflex Hose will advise when the enquiry is made.
Visiflon TO Grades - The MWP listed above applies up to a maximum temperature of 100˚C (212˚F).
Visiflon SS Grades - The MWP listed above should be reduced by 1% for each 1˚C above 130˚C up to a maximum of 230˚C (1% for each 1.8˚F above 266˚F up to a maximum of 450˚F).
Visiflon PB Grades - The MWP listed should be reduced by 5% for each 1˚C above 80˚C up to a maximum of 100˚C (5% for each1.8˚F above 176˚F to 212˚F).
Visiflon SS Grades are vacuum resistant to -0.9 bar up to 130˚C (266˚F).
Visiflon TO and PB Grades are vacuum resistant to -0.9 bar up to 80˚C (176˚F).
The internal convolutions restrict flow rates due to turbulent flow, and may also cause a whistling noise when gases are passed through. For any applications where this may be a problem, the alternative Aflex Hose products Hyperline FX or Corroline would provide a solution.
