How to Order

How to Order

The quantity, hose size, liner, braid, cover, protection system, length and fittings must be selected and specified in full.

EITHER by a full, written description. The hose grade can be specified by the code initials e.g. “FaBLINE AS, SS, RC, ” defines an antistatic PTFE lined hose with an EPDM rubber cover over a SS braid. The quantity, length and fittings can then be written in - e.g. “4 off x 1” bore FaBLINE, AS, SS, RC, x 3.00 metres long. Both ends non-lined ANSI 150# S/S Flanges”.

OR by Part Numbers. Example from above “4 off Part No. 16-AFXF/AS-RC-00-3.00m-12-12”.

Any special requirements relating to the hose construction, or information required on Tags, or Certificates, or special testing of requirements, must be specified in full on the enquiry or purchase order.

Selecting the Hose Grade

There are two types of PTFE liner available, natural (GP) and antistatic (AS) other external protection systems are also available.

A hose grade is specified by using the abbreviations given. For example, FaBLINE AS, PC would describe a hose with an antistatic PTFE liner and a SS wire protection Coil.

Selecting the End Fittings

FaBLINE is available with a range of ‘standard’ end fittings, normally supplied hygienically PTFE lined and flared.

Stainless Steel End Fitting Materials

  • Non-Lined Spigots - are made from Grade 316L SS
  • PTFE Lined Spigots - are made from Grade 316L or Grade 316C SS
  • Cam and Groove Female Fittings - are made from Grade 316C SS (Body) and 316L SS (Spigot)
  • Swivelling Nuts and Flanges - are made from Grade 304 SS
  • Ferrules - most ferrules are made from Grade 304 SS, except some are made from Grade 316L SS - consult Aflex Hose if necessary.

The equivalent specification for the different Grades of Stainless Steel are listed below:

Specification Equivalents List

Grade BS - British Standard AISI - American Standard or C = Casting Grade EN - European Norm
316L SS BS 316 S11 AISI 316 L EN1.4404
316C SS BS 316 C16 CF8M EN 1.4408
304 SS BS 304 S15 AISI 304 EN 1.4301

 

To special order, end fitting components can be made in nonstandard grades of SS such as 1.4435, or other materials such as Hastelloy or Monel.

Conditions of Sale

FaBLINE hose and hose assemblies are only supplied on the basis that the customer has read and accepted the Conditions of Sale. Customers own Conditions of Sale (or equivalent) are not accepted unless an acceptance, signed by a Director of Aflex Hose is supplied.

Selecting the Hose Length

FaBLINE hose assemblies are made up to the specific lengths required. The hose length is taken as the length from the sealing face at one end of the hose to the same at the other end. The length tolerance is normally +2% / -0%. Closer tolerances are available to special order. (see also Length Calculation)

 

FaBLINE Hose Assembly Length Limitations*

Nominal Size of Hose Minimum Hose Length Used Straights Minimum Hose Length Flexed through 90 ° Maximum Hose Assembly Length
in dn in mm in mm ft mtrs
1/4 6 3 75 3 75 100 30
3/8 10 3 75 3 75 100 30
1/2 15 3 75 3 75 100 30
5/8 16 3 75 3 75 100 30
3/4 20 3 75 4 100 100 30
*7/8 22 3 75 4 100 100 30
1 25 4 75 4.33 110 100 30
11/4 32 4 100 6.3 160 100 30
*1 3/8 35 4 100 7.48 190 100 30
1 1/2 40 4 100 8.66 220 100 30
*1 7/8 48 4 100 11.81 300 100 30
2 50 4 100 12.4 315 100 30
21/2 65 4 100 18.7 475 60 18
3 80 4 100 21.65 550 50 15

*Listed minimum lengths are for the FaBLINE Hose only, and DO NOT INCLUDE THE LENGTHS OF THE FITTINGS AT EACH END. These must be found from the end fitting pages and added to calculate the minimum length of the hose assembly.

**Longer lengths may be available to special order.